منصة عالمية متكاملة لتوريد الآلات الهندسية
جلوبال ماتشكس
منصة عالمية متكاملة لتوريد الآلات الهندسية
جلوبال ماتشكس
801101745 CR HMS5 70×95×10 Radial Shaft Oil Seal for XCMG Loader Engine

801101745 CR HMS5 70×95×10 Radial Shaft Oil Seal for XCMG Loader Engine

USD $9.00 / قطع

الحد الأدنى للطلب: 20 قطع

شروط التجارة المدعومة:
FOBEXW
السعر المرجعي:
USD $9.00
الحد الأدنى لكمية الطلب:
20 قطع
مهلة التسليم:
15-20 days after deposit
القدرة على التوريد:
1,000 قطع
ميناء الشحن:
Shanghai/Ningbo/shenzhen
إرسال استفسار

801101745 CR HMS5 70×95×10 Radial Shaft Oil Seal — for XCMG Loader Engine & Rotating Machinery

The oil seal (Part No. 801101745, CR HMS5 type, 70×95×10) is a radial shaft seal​ designed for rotating shaft applications in XCMG loader engines and related drivetrain components . As a spring-loaded, single-lip rotary shaft seal, it retains lubricant (oil or grease) on the oil side while preventing contaminants from entering on the air side — a critical barrier protecting bearings, gears, and rotating assemblies from premature failure due to lubrication loss or particulate ingress.

Built to CR HMS5 / SKF HMS5 specification​ :

Parameter

Specification

Design

HMS5 (rubber outside diameter, single sealing lip)

Shaft Diameter (d)

70 mm

Housing Bore Diameter (D)

95 mm

Seal Width (b)

10 mm

Sealing Lip Material

Nitrile Rubber (NBR) — RG compound

Outside Diameter Type

Rubber metal reinforced (beaded OD)

Spring

Garter spring (stainless steel)

Auxiliary Lip

No

Standards

ISO 6194, DIN 3760

Net Weight

0.0502 kg

Performance envelope​ (per SKF official data) :

  • Operating temperature:​ -40°C to +100°C (short-term up to 120°C)

  • Max. circumferential speed:​ 9.2 m/s

  • Max. rotational speed:​ 2520 r/min

  • Pressure differential:​ 0.05 N/mm² (max 0.05 MPa / 7 psi)

  • Lubricant compatibility:​ Mineral oils, grease, low-viscosity oils, synthetic lubricants (moderate temp.)

Key design advantages​ (from SKF CR HMS5 engineering notes) :

  • The rubber outside diameter​ provides optimized sealing ability in the housing, even at considerable surface roughness or in split housings

  • The beads on the outside diameter​ improve sealing ability and retention in the bore, and prevent spring-back during installation

  • The spring-loaded sealing lip​ responds quickly to dynamic runout and maintains sealing performance even when lip wear is excessive

  • The optimized NBR (RG) compound​ offers good resistance to ageing, very good pumping ability, and good wear resistance — rapidly returning oil from the air side to the oil side

Application & Compatibility

This oil seal is designed for XCMG loader engine and rotating shaft applications:

Primary application:​ XCMG loader engine​ — SourcingAI's listing explicitly states "Spare Parts CRHMS570X95X10 Oil Seal 801101745 for XCMG" with application = "Loaer Engine" (loader engine) .

Typical installation points​ (where 70×95×10 HMS5 radial shaft seals are commonly used across construction machinery):

Application Area

Typical Use

Engine​

Crankshaft seal, camshaft seal, accessory shaft seal

Transmission / Gearbox​

Input/output shaft seals, gear reducer seals

Axle / Final Drive​

Wheel hub seals, differential seals

Hydraulic Components​

Pump shaft seals, motor shaft seals

Rotating Machinery​

Any 70mm shaft × 95mm bore × 10mm width rotary seal point
إرسال استفسار